Engine parts & Cooling parts
|
Reconditioned parts
From stock on exchange basis only
|
Cylinderhead 1494, 1592, 1725 (Alu, Cast Iron)
Short engines (1494, 1592, 1725)
Diff unit (3.89-4.22)
Gearbox (3 synchro, 4 synchro, overdrive A type, D type)
|
|
|
Now new in stock
Engine mounts Minx, Rapier series 1-2
2.5 cm high
Made with the correct rubber compound. Not too soft, not too hard. You will notice direct the difference in engine vibration !!!
Price 19,50 + VAT
|
2.5 cm high
|
Engine mounts FOR
Hillman S. Minx MK1 Humber Vogue (Austr.)
4.5cm high
Made with the correct rubber compound. Not too soft, not too hard.
Oil resistant.
You will notice direct the difference in engine vibration !!!
Price 19,50 + VAT
|
4.5cm high
|
New Camshafts for the 1494 and 1592 Alu head engines
Only € 179,50 !
Allways replace camfollowers when rebuilding your engine!
|
|
Camshafts for the 1725 Alu head engines
Only € 169,50 !
|
|
Oilpump repair set 5220340
for our 1592 engines.
Rotor, vane and hardened shaft
Offer price € 59.50 +VAT
For series 2-4
|
|
Camfollowers for 1390, 1494, 1592 and 1725 Alu head engines
Offer price € 9.50 +VAT
|
|
Rear wheel bearings
Original specs ! 9188096 Bearing Rear axle shaft 1390, 1494, 1592 P.43652
Now new in stock
Price € 47.50 +VAT
|
|
1801176 Wheelbearing & seal 1725 (75221451)
Original specs ! C3 bearing
Now new in stock
Price € 49.50 +VAT
|
|
Rocker- shaft (pair)
Avaliable for alu and cast iron head (1390-1725cc)
Now new in stock
Price € 69.50 +VAT
|
|
|
|
Main bearing set 1956-1967 (1390, 1494 and 1592)
STD, 010", 020" and 030" for the 1390, 1494 and 1592 Sunbeam, Hillman, Singer and Humber 4 cylinder engines..
Offer price € 59.50 +VAT
For series 1-4
|
|
Big end bearing sets 1592 cc and 1494 cc
STD, 010", 020" and 030" for the 1494 and 1592 Sunbeam, Hillman, Singer and Humber 4 cylinder engines.
Offer price € 59.50 +VAT
Please state for 1494 cc or 1592 cc
|
|
|
|
Main bearing set 1967- (1725)
For the 1725 Sunbeam, Hillman, Singer and Humber 4 cylinder engines..
Offer price STD, 010", € 69.50 +VAT
020" and 030" and 040 € 39.50 +VAT.
Some 050 and 060 available at request
|
|
Big end bearing sets 1725 cc
STD, 010", 020" and 030" for the 1725 Sunbeam, Hillman, Singer and Humber 4 cylinder engines.
Offer price STD, 010", € 69.50 +VAT
020" and 030" and 040 € 39.50 +VAT.
050 and 060 available at request
|
|
Original water pumps
For all 1592 and 1725 cc engines.
Designed for better flow and uprated pressure.
Cast iron creates less corrosion.
Height approx 130mm
Price € 72.50 +VAT outright !
|
Height approx 130mm
|
Original water pump 1390 and 1494 cc engines
For all 1390 and 1494 cc engines, now in stock again!!
Designed for better flow and uprated pressure.
Cast iron creates less corrosion.
Height approx 100 mm
Price € 79.50 +VAT
|
Height 85 mm
|
NEW
Waterpump repair kit:
Early models 1948-54 Side valve
This kit comprises new bearing, impeller and seal
Some parts in stock for side valve engines
Price €79.50+VAT
Waterpump repair kit:
1955-61 OHV 1390/1494
This kit comprises bearing and seal
Please state model/serie when ordering !!!
Price €39.50+VAT
|
|
NEW
Waterpump Impellor
4 Cylinder petrol OHV 1955-60
4 Cylinder petrol OHV 1961-68 1592/1725
40 € plus VATPlease state model (series) when ordering !!!
|
|
Thermostat cover
Thermostat Housing Cover
Pressure die cast!
Late 1592 and 1725 aluminium head models
€ 34,50 + VAT
|
|
NEW
1208229 Water outletpipe / Thermostat cover
Thermostat Housing Cover
Pressure die cast!
Early 1592 models
Offer price € 34.50 +VAT
|
|
|
|
Thermostat housing 1963 onwards
Complete with gaskets
Offer price 59.50€
|
|
Starterring gear
Made by an original supplier.
Avaliable for all 1390, 1494, 1592 and 1725 engined cars.
€ 69.95 plus VAT
|
|
Crankshaft Pulley (excl damper)
High quality remake of the original "Metalastic" type pulleys fitted form 1956 onwards on for Aluminium head engines only
Lightweight (LM13) & pre balanced.
Price € 89,50 + VAT
|
|
|
Door handle, outer front (only)
(handed; in pairs)
Assembled, you use your own set of barrels and keys
Price per pair: € 165+VAT
|
|
New Hornring
Humber Sceptre MK2
Rapier series 4-5
99.50€
|
Box is shown for display purposes only).
|
Electronic and standard distributors
Distributors for 1600 and 1725 alium head engines.
This is a late 45D4 Lucas type version, specially made for us.
Both versions avaliable for Alu and Cast Iron head cars !
The electronic version Neg earth car only !
45DE4 Electronic 195€ plus vat
Buy now 149,50€
45D4 standard version 140€ plus VAT
Buy now 99€
|
Contact breaker less version 45DE4
Below the standard model
|
|
|
Steering and suspension
|
New! Center steering rod 5220976 (QDL990)
Now again available in limited supply: The center steering rod with ball joints and grease nipples like the original Rootes part.
The rubber bushed model was introduced in the 60's as cheaper to produce part removing grease points.
This is the ultimate replacement part for your car. No sloppy, in secure steering anymore!!
Price € 79.50+VAT
Offer price 69.50€ +VAT
|
Shock absorbers
Monroe Front shock-absorbers for Superminx, Vogue, Sceptre 1961-65 and later Minx Gazelle, Rapier Venezia
|
Price € 179.50+VAT
Offer price 129.50€ +VAT
|
Rear shock-absorbers for Superminx, Vogue, Sceptre 1961-65
Venezia
|
Price € 179.50+VAT
Offer price 129.50€ +VAT
|
SPAX adjustable front shock-absorbers for
Hillman Minx 1-3c
Sunbeam Rapier 1-3
Singer Gazelle 1-3c
Hillman Husky 1-3
Commer Van 1-3
(please forward chassisnumber)
|
Price € 179.50+VAT
Offer price 129.50€ +VAT
|
Rear shock-absorbers for Minx, Rapier and Gazelle Husky
Series 3 onwards (please forward chassisnumber)
|
Price € 179.50+VAT
Offer price 129.50€ +VAT
|
Fulcrum pin silent bushes
Original "Metalastic" type
Metal bonded bushes.
Proper fit, give back that original ride to your car!
Quantity per side: 2
Top fulcrum bush (each) Price €11.25 +VAT
Lower fulcrum bush (each) Price € 13.50 +VAT
|
|
NEW Top fulcrum pin and bush set 1961-
1224225
Pin c/w rings and nuts, bush separate availiable
€ 69,50 plus vat
|
|
NEW Bottom fulcrum pin and bush set 1961-
1224224
Pin c/w rings and nuts, bush separate avaliable
€79,50 plus vat
|
|
Relay lever pin (remote steering lever)
All Alpines 1959-67
Offer price 45 € +VAT
a K.24275 Bush, steering only is 8.25 € +VAT
|
Relay lever repair kit 1955-1967
(in picture part 6)
Replacement steering idler pin as original Rootes part in design and quality.
Kit includes 2 bushes
|
Kingpin set P.48890
Sunbeam Alpine 1-3 Sunbeam Rapier 1-4 Hillman Minx 1-4 Singer Gazelle 1-3 Commer Cob
Price € 49.50 per side+VAT
|
|
Track rod ends
1 Pair:
Left-hand & right-hand thread
Alpine all models 1959-
|
Offer price € 42.50+VAT
|
Track rod shaft
1956-1967 Sunbeam Rapier 1-4 Hillman Minx 1-4 Singer Gazelle 1-3 Commer Cob, Superminx, Vogue, Sceptre 1961-65
Venezia
This is the shaft that connects the 2 balljoints.
It comes including the 2 special nuts (left hand / right hand thread) Price € 21.50+VAT Offer price 17.50€ +VAT
Price excludes the balljoints !
|
|
Top fulcrum pin and bush set (P.48612)
Sunbeam Alpine 1-3 Sunbeam Rapier 1-4 Hillman Minx 1-4 Singer Gazelle 1-3 Commer Cob
Price per side € 69.50+VAT
|
|
Lower fulcrum pin and bush set (P.48610)
Sunbeam Alpine 1-3 Sunbeam Rapier 1-4 Hillman Minx 1-4 Singer Gazelle 1-3 Commer Cob
Price per side
€ 79.50+VAT
|
|
P108345/P108341 Lower Eyebolt and Bush Outer series I - III
Sunbeam Alpine 1-3 Sunbeam Rapier 1-4 Hillman Minx 1-4 Singer Gazelle 1-3 Commer Cob
Outer lower fulcrum pin and bush set
Price per side € 29,50+VAT
|
|
Bump stop
front suspension
Superminx, Vogue, Sceptre 1961-65, Venezia, Minx series
Top (1214933 p.100587)
Bottom (1207804 1216035) pan
Original design & UNF thread
Price
Top € 9.50+VAT
Bottom € 12.00 + vat
|
|
Ball joint (Bottom) 1963-
Humber Sceptre, Hillman Super Minx, Singer Vogue
Minx, Gazelle, Commer Cob, Husky
Price € 67.50+VAT Offer price 52.50€ +VAT
|
|
Ball joint (Top) 1963-
Humber Sceptre, Hillman Super Minx, Singer Vogue
Minx, Gazelle, Commer Cob, Husky
Price € 45+VAT Offer price 42.50€ +VAT
|
|
Top ball-joints for:
1223762 Ball Joint Upper '59-61
Sunbeam Alpine 1-3
Hillman Minx 1-3c
Sunbeam Rapier 1-3
Singer Gazelle 1-3c
Hillman Husky 1-3
Commer Van 1-3
Price € 65+VAT Offer price 49.50€ +VAT
|
|
Rear suspension
|
Rear spring front bush, large offset
9188167
|
Price € 16+VAT
|
Rear spring rear bush,
9188018
|
Price € 9.50+VAT
|
|
|
Gearbox parts
|
Layshaft Gearbox
Covers all models 1952-76. Except Imp, Avenger and 6 cylinder Humber
Price € 34.75+VAT
|
Bush rear cover
std gearbox
5220886
|
|
New! Engine mounts
Rapier 1-2
2.5 cm high
Made with the correct rubber compound. Not too soft, not too hard. You will notice direct the difference in engine vibration !!!
Price € 19,50 + VAT
|
|
New! Engine mounts
Hillman S. Minx MK1
Humber Vogue (Austr.)
4.5cm high
Made with the correct rubber compound. Not too soft, not too hard.
Oil resistant.
You will notice direct the difference in engine vibration !!!
Price € 19,50 + VAT
|
|
|
Synchromesh rings
All 4 synch models
5220875
Price € 24.75+VAT
|
|
Differential gear set (1961-)
New set gears and shaft for the Rootes Diff unit 1961 onwards (fine spline)
Price € 89,50 +VAT
|
|
:
:
New crown wheel and pinion set
All models Alpine 1:4.22 ,1: 3.89
Price 295 € + vat
|
|
|
|
|
|
Most brake parts in stock
|
|
|
Valve Guides
Made by an original supplier.
Set of 8 : 4 inlet, 4 exhaust.
Avaliable for all 1390, 1496, 1592 and 1725 engines, alu or cast iron head.
Price per set (4+4) € 49.50 only!
|
|
Pistons for 1592 and 1725 engines !
Sizes STD, +0.30"
and +0.40"
€ 295
( incl rings, clips and pins)
plus VAT where appl.
The most common size sold was 030", but we had demand for other sizes of our premium quality pistons.
From now we have the sizes 0.20", 0.30", 0.40", and even ...... 0.50" (price at request)
Click here to see more about these pistons and rings!
|
|
|
|
Many parts in stock for all models 1970-81. Please sent email for more information
|
For windscreens please check here
|
|
|
|
|